Коды ошибок копировальных аппаратов
iR2200 / iR2800 / iR3300

Error Code	Detail Code	Error Name/Explanation of Error
E000	0000	The reading of the main thermistor does not reach 30°C 1 sec after the main power switch is turned on. Or, it does not reach 70°C 2 sec thereafter.
E001	0000	The main thermistor detects 250°C or higher.
	0001	The main thermistor or the sub thermistor detects overheating (hardware circuit detection).
	0002	The sub thermistor detects about 295°C or higher.
E002	0000	The temperature of the fixing film is as follows: has exceeded 100°C, but does not reach 115°C within 1 sec thereafter. has exceeded 140°C, but does not reach 150°C within 1 sec thereafter. has exceeded 160°C, but does not reach 165°C within 1 sec thereafter.
E003	0000	The main thermistor reading is lower than 140°C when paper is moved.
	0001	Low fixing temperature detection after standby (by sub thermistor)
E007	0000	An error in the rotation of the fixing film is detected. The reading of the main thermistor is 100°C or higher and, in addition, the fixing film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven.
E010	0000	After the main motor drive signal is generated, the clock signal does to arrive within 1.3 sec.
E014	000	After the fixing motor drive signal is generated, the clock signal does not arrive within 1.3 sec.
E019	0000	The waste toner case is full of waste toner.
E032	0001	The DA unit connection is disconnected (after connection).
E051	0000	At start-up, home position is not detected when the horizontal registration assembly is moved 100 mm in the direction of home position.
E064	0000	The presence of a high-voltage error is communicated by the composite power supply PCB. (The output for primary charging, developing, or transfer has deviated from a specific level of voltage.)
E100	0001	The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal.
	0001	The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal.
	0002	While the laser is ON, the BD signal cycle is outside a specific range 20 times or more continuously.
	0003	While the laser is ON, the horizontal sync signal cycle is outside a specific range 20 times or more.
E110	0000	The motor ready signal does not arrive within 15 sec after the laser scanner motor drive signal is generated.
E202	0001	The scanner home position sensor does not go OFF when the scanner is moved forward by 40 mm.
	0002	The scanner home position sensor does not go ON when the scanner is moved reverse 450 mm.
E204	0001	While an original is being read, the image leading edge signal does not arrive from the ADF.
E220	0001	A fault is detected on the inverter PCB for the scanning lamp.
E225	0000	A specific level cannot be attained for the signal during CCD gain correction at power-on.
	0002	The edge gain correction level is different from the correction level for the preceding sheet by a specific level or more.
E240	0000	A fault occurs in communication between the CPU of the main controller PCB and the CPU of the DC controller PCB.
E243	0000	A fault occurs in the communication between the CPU of the control panel PCB and the CPU of the main controller PCB.
E248	0001	A difference is discovered between the ID in EEPROM read when the main power switch is turned on and the ID in ROM upon comparison.
	0002	The data read does not match the data written to EEPROM.
	0003	A difference is discovered between the ID of EEPROM and the ID of ROM upon comparison while writing data.
E261	0000	The intervals of zero-cross signals deviate from the tolerance range while the fixing heater is supplied with power.
E302	0001	During shading, the shading processing does not end on the reader controller PCB after 1 sec.
	0002	During stream reading, the edge white addition processing does not end on the rear controller PCB after 10 sec.
E315	-	Any of the following is true in the image processing by the main controller: The image data has a fault. The encoding/decoding operation for image data has a fault. The image processing element of the main controller PCB has a fault.
E601	0000	When an image is transferred between the main controller PCB and the HDD, the main controller PCB detects a fault in control information.
	0001	When an image is transferred between the main controller PCB and the DC controller PCB, the DC controller PCB detects a fault in the control information.
E602	0001	A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM.
	0002	A data read fault of the HDD is detected when the HDD is started up from the BOOT ROM.
E604	0000	A fault is detected in the image memory.
E605	0001	A fault is detected in the battery for the image memory.
E606	0001	A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM.
E674	0000	A faulty occurs in the communication between the fax PCB and the main controller PCB.
E677	0001	A fault occurs it the combination between any of the printer boards (accessories) and the main controller PCB.
E710	0001	When the main power is turned on, the communication IC (IPC) on the reader controller PCB cannot be initialized.
	0002	When the main power is turned on, the communication IC (IPC) on the DC controller PCB cannot be initialized.
	0003	When the main power is trend on, the communication IC (IPC) on the main controller PCB cannot be initialized.
E711	0001	Data is written to the error register of the communication IC (IPC) on the reader controller PCB four times or more within 1.5 sec.
	0002	Data is written to the error register of the communication IC (IPC) on the DC controller PCB four times or more within 2 sec.
	0003	Data is written to the error register of the communication IC (IPC) on the main controller PCB four times or more within 2 sec.
E712	0001	The communication is not resumed 3 sec or more after data has been written to the error register of the communication IC (IPC) on the ADF controller PCB.
	0002	The transmission bit is not enabled 10 sec or more in the sync register of the communication IC (IPC) on e reader controller PCB.
E713	0000	The communication with the finisher is not resumed 3 sec or more after it is disrupted.
E716	0000	The ID signal is not detected within a specific period of time after the presence of a pedestal is detected.
E719	0000	Erroneous communication with card reader (serial communication)
	0002	Erroneous communication with coin vender (serial communication)
E717	0001	The communication with the DA unit is not resumed 3 sec or more after it is disrupted.
E719	0001	The communication between the Card Reader-C1 or the coin vendor and the main controller PCB is disrupted.
E732	0001	A fault is detected by the main controller PCB in the communication between reader controller PCB and the main controller PCB.
E733	0001	A fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB.
E737	0000	During self diagnosis at power-on, the DRAM check finds a fault in the main controller PCB.
E740	0001	At power-on, the LAN card has a fault.
	0002	The MAC address has a fault.
	0003	The LAN card cannot be read.
E741	0000	The PCI bus has a fault.
E743	0000	The reader controller PCB detects a fault in the communication between the main controller PCB and the reader controller PCB.
E744	0000	The BootROM on the main controller PCB and the system software are for different models or are of different types.
E803	0000	The 24V output from the composite main power supply PCB is absent for 1 sec or more.
E805		The clock signal is absent for 5 sec or more after the fan drive signal has been generated. The detail codes of the fans in question are as follows:
	0001	developing fan (FM1)
	0002	fixing fan (FM2)
	0003	curl reducing fan (FM4)
	0004	curl reducing fan (FM5)
	0005	electrical unit fan (FM3)
E901	0000	The motor ready signal does not arrive within 1.3 sec after the pedestal main motor drive signal is generated.
ADF Error Codes
E420	0001	When the power switch of the host machine is turned on, the back-up data from the EEPROM cannot be read or the data that has been read has a fault.
E421	0001	The back-up data cannot be written to the EEPROM, or the data that has been written has a fault.
E422	0001	While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0.5 sec or more.
Saddle Finisher-G1 Error Codes
E501	0001	The communication between the finisher controller PCB and the puncher drive PCB is disrupted.
E505	0001	When the main power is turned on, the checksum of the finisher controller PCB has a fault.
	0002	When the main power is turned on, the checksum of the puncher driverPCB has a fault.
E510	0001	The feeding roller does not leave home position when the feed motor is driven for 2 sec.
	0002	The feeding roller does not return to home position when the feed motor is driven for 2 sec.
E514	0001	The delivery belt does not leave home position when the stack delivery motor is driven for 3 sec.
	0002	The delivery belt does not return to home position when the stack delivery motor is driven for 3 sec.
E530	0001	The aligning plate (rear) does not leave home position when the alignment motor (rear) is driven for 3 sec.
	0002	The aligning plate (rear) does not return to home position when the alignment motor (rear) is driven for 3 sec.
E531	0001	The stapler does no leave home position when the stapler/folder motor is driven for 1.5 sec.
	0002	The stapler does not return to home position when the stapler/folder motor is driven for 1.5 sec.
	0003	The clock signal is disrupted for 1 sec or more while the stapler/folder motor is driven.
E532	0001	The stapler unit does not leave home position when the stapler slide motor is driven for 4.5 sec
	0002	The stapler unit does not return to home position when the stapler slide motor is driven for 4.5 sec.
E537	0001	The aligning plate (front) does not leave home position when the alignment motor (front) is driven for 3 sec.
	0002	The aligning plate (front) does not return to home potion when the alignment motor (front) is driven for 3 sec.
E540	0001	The paper surface sensor remains unchanged 10 sec after the tray ascent/ descent motor is driven.
	0002	The tray upper sensor goes ON while the tray is moving up.
	0003	The clock for the clock sensor is disrupted for 10 sec or more while the tray ascent/descent motor is driven.
E577	0001	The paddle does not leave home position when the paddle motor is driven for 2 sec or more.
	0002	The paddle does not return to home position when the paddle motor is driven for 2 sec or more.
	0003	The stack ascent/descent guide does not leave home position when the paddle motor is driven for 2 sec or more.
	0004	The stack ascent/descent guide does not return to home position when the paddle motor is driven for 2 sec or more.
E590	0001	The puncher does not return to home position when the puncher motor is driven for 250 msec.
	0002	The clock from the puncher motor clock sensor is disrupted for 60 msec or more when the puncher motor is driven.
E592		In the course of sensor output automatic adjustment, the light-receiving voltage is 2.5 V or less even when the light-emitting voltage is set to 4.4 V. In the course of output automatic adjustment, the light-receiving voltage is 2.5 V or more even when the light-emitting voltage is set to 0 V. In the course of sensor output automatic adjustment, the light-emitting voltage is set to 4.4 V or more.
	0001 to 0005	Horizontal registration sensor
	0006	Puncher waste full sensor
E593	0001	The puncher not leave home position when the puncher shift motor is driven for 1 sec.
	0002	The puncher does not return to home position when the puncher shift motor is driven for 1 sec.
E5F1	0001	The folding roller does not leave home position when the stapler/folder motor is driven for 1.5 sec.
	0002	The folding roller does to return to home position when the stapler/folder motor is driven for 3.5 sec or more.
	0003	The clock is disrupted for 1 sec or more while the stapler/folder motor is driven.
Finisher-J1 Error Codes
E500	0000	The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less.
E514	0000	At the start of the motor CW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON.
E530	0000	The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go ON. The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go OFF.
E531	0000	The stapling home position sensor (S16) does not go off 0.5 sec after the stapler motor is rotated CW. The stapling home position sensor (S16) dos not go ON with 0.5 sec after the stapler motor is rotated CW and, thereafter, the sensor does not go ON within 0.5 sec after the motor is rotated in reverse.
E537	0000	The aligning plate home position sensor (S6) does not go ON when the front alignment motor (M3) is driven for a specific number of rotations. The aligning plate home position sensor (S6) does not go OFF when the front alignment motor (M3) is driven for a specific number of rotations.
E577	0000	The return roller does not reach home position when the delivery motor (Ml) has been driven as much as will move it to the return roller home position sensor (S3).
E580	0000	The delivery tray upper limit sensor (S13) goes ON while the delivery tray ascent/descent motor (M5) is in operation. The clock signal of the delivery tray ascent/descent motor clock sensor (S9) is not detected 15 times or more within 0.8 sec while the delivery tray ascent/ descent motor (M5) is in operation. The delivery tray paper height sensor (S10) does not go ON 4 sec after the delivery tray ascent/descent motor (M5) starts to move up. The delivery tray paper height sensor (S10) does not go OFF 4 sec after the delivery tray ascent/descent motor (M5) starts to move down.
E585	0000	At the start of the motor CCW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON.